KT-1-PCB One door controller PoE, PoE+ or 12Vdc, including: Plastic Housing and 13,8Vdc 3A power Supply

KT-1-PCB One door controller PoE, PoE+ or 12Vdc, including: Metal Housing and 13,8Vdc 3A power Supply

KT-1 One door controller with PoE+ battery charger is a KIT part of KT-1-PCB + KT-1-CAB-POE

One KT-1, IP Controller Single gang flush Mount, PoE, PoE+ or 12Vdc, (KT-1 only, no PSU)

One KT-1-PCB, IP Controller PCB with metal cabinet PoE, PoE+ or 12Vdc, including KT-1-PCB and Metal housing, No PSU)

One Door IP Controller ` including connector board (Compatible with KT-1-CAB-M or P)

Plastic enclosure ONLY for KT-1-PCB

Metal enclosure ONLY for KT-1-PCB

Metal enclosure with PSU for KT-1-PCB, Switch Mode 12 Volt 2A Power Supply, Mains and Battery Monitoring outputs. A universal mains voltage input (90 to 264 Volts a.c.) Dimensions 275H x 330W x 80D, Space to house a 12V 7Ah Battery

Metal enclosure with Battery backup PoE for KT-1-PCB, PoE+ (PoE 802.3at) 16W including battery charge. Supplies battery back-up on loss of PoE power. Dimensions 275H x 330W x 80D, Space to house a 12V 7Ah Battery

Switching power supply for Controllers - Max Current 3,6A @ 13,8V, Dimension :129x98x38mm (LxWxH), input voltage range 85 ~ 264VAC, Protections, Short circuit / Overload / Over voltage / Battery /polarity protections (by fuse)

Black Replacement cover for KT-1/ Including back box

KT-1-PCB backplate only, (KT-1 not included).

KT-2 Two Door Controller kit with KT-2 Metal Cabinet including PSU, 13.8Vdc 4 x 1A: 1 x KT-2-PCB-EU 1 x KT-2-CAB-PSU

KT-2 Metal Cabinet including PSU, 13.8Vdc 4 x 1A / Front & Rear Tamper / Accommodates 12V 7Ah battery

KT-2 Two Door Controller and connector backplate, no cabinet

KT-2 controller backplate replacement, Wi-Fi antenna, no cabinet.

Metal mounting plate for migration of KT-300 and KT-200 with KT-2 Controller

Boxed version of KT-4 four door, (EMEA and APAC )IP ready controller comprising PCB, Housing and 240/16Vac transformer

KT-4 PCB with PoE Module on board, accessory kit and metal cabinet with lock and keys

KT-4 / KT-4-EU 4 reader controller

PoE++ module add-on for KT-4-PCB

WiFi module and antenna add-on for KT-4-PCB, requires version 8,71 and higher

Black metal cabinet for KT-4-EU. Includes cabinet, detachable door, artwork and camlock. Does not include power supply

Black metal cabinet for KT-4 (US version). Includes cabinet, detachable door, artwork and camlock. Does not include power supply

Kantech controllers Removable terminal block kit.

Accessory kit including: 1.0K ohm (2), 5.6K ohms (10), 120 ohms (2), PCB standoff, lock hole cover, ground wire and screwdriver

KT-400/KT-4 transformer, wire-in, 240 VAC/ 16 Vac (100 VA), CE approved

RS-485 Input/Output Module for KT-1 and KT-400, 45 mA when AUX+ output is not sourcing any current. 1.6 A max. when AUX+ output is sourcing 1.5 A current. (31.5 x 146 x 82.6 ). Input mode: I/Os that are configured as inputs support normally closed (NC) and normally open (NO). contacts. They support no end-of-line, single end-of-line, and double end-of-line zone loops. Output mode: I/Os that are configured as outputs (open-drain outputs) can sink up to 750 mA each. Each module can sink a maximum of 4 A. I/Os #9 to #12 that are configured as SPI ports can support a daisy-chained SPI bus that is made up of 8 KT-MOD-REL8 modules. Each of these modules can provide 8 Form C relay outputs .firmware field upgradable via RS-485.

16-zone, input expansion module with SPI cable (KT-MOD-SPI-16)

16-zone output expansion module with 40 cm SPI cable (KT-MOD-SPI-16)

Eight-relay expansion module with SPI cable (KT-MOD-SPI-16)

KT-400 SPI Cable 16 inch

KT-400 SPI Cable 36 inch

Expansion Module cabinet, black, with 92 cm SPI cable (KT-MOD-SPI-36) and lock (KT-LOCK)